Skip to content
Website
🧱 CFC 281Drying, heat-up and moisture measurementsChapter 2 of 10 in the section

The electrical moisture meter: indicative only, and why it never replaces measurement

This chapter teaches you how to use the pin-type or dielectric electrical device to map the drying of a screed without engaging your civil liability. You will learn how to identify the pitfalls related to surface salts and temperature, while mastering the decisive role of the reference measurement to legally authorise the installation of floor coverings.

Key takeaways

  • The electrical moisture meter offers rapid scanning without destroying the work but remains a purely indicative measurement.
  • Salt concentration and ambient temperature severely distort the electrical resistance of the mortar.
  • The device is used solely to locate the wettest area in order to carry out sampling.
  • Only the calcium carbide bomb test prescribed by standard SIA 251 is authoritative.

The physical principle of the electrical device and its limits on mineral screed

On Swiss construction sites, the electronic pin-type or capacitive contact moisture meter has become a familiar tool for site monitoring. Its use consists of measuring an indirect physical quantity, most commonly the electrical resistance or dielectric permittivity of the mortar between two electrodes or under a contact plate. The device then converts this impedance into a numerical value, displayed in equivalent mass percentages or arbitrary digital units. This speed of execution makes it possible to perform dozens of checks in a few minutes, without leaving visible traces on the liquid or traditional screed.

This rapid reading conceals a major flaw: the device does not quantify the free water trapped in the porosity of the material, but reacts to the passage of a micro-current. Electrical conductivity strongly depends on factors completely independent of the actual moisture of the mineral substrate:

  • The content of soluble salts and free alkalis which migrate to the surface during evaporation and artificially increase the conductivity of the mortar.
  • The exact composition of the binder, in particular the presence of plasticisers, retarders or metal fibres which modify the intrinsic resistance of the screed.
  • The temperature of the screed, knowing that floor heating lowers the electrical resistance and drives up the displayed value without adding water.
  • The compaction density and surface porosity of the mortar at the exact contact point of the test pins.
Comparative behaviour of moisture control methods
Parameter analysedPin-type electrical moisture meterDielectric contact deviceCalcium carbide flask
Controlled depthSuperficial (2 to 5 mm)Medium (10 to 30 mm)Entire sampled thickness
Salt sensitivityVery strong disturbanceModerate disturbanceInsensitive to salts
Temperature influenceSignificant driftModerate driftZero on chemical reaction
Role on the construction siteMapping and locationGlobal mappingRecognised release measurement

Basing a decision to install a floor covering on an electrical moisture meter figure exposes the screed layer and the flooring contractor to serious defects: blistering of waterproof membranes, detachment of polymer adhesives or irreversible deformation of high-end parquet floors under the effect of background moisture.

The legal value of the measurement according to standard SIA 251 and risk management

For construction law in Switzerland, the acceptance and admissibility of a work are governed by recognised rules of the art. Standard SIA 251 precisely defines the requirements applicable to floating and bonded screeds, including the permissible residual moisture thresholds before the installation of each finish family. This standard does not recognise any legal equivalence for electronic or capacitive measuring devices to certify the final dryness of a screed.

The measurement of the residual moisture of a screed authorising the installation of a floor covering must be carried out by the calcium carbide method (CM method) or by oven drying gravimetric testing.

Norme SIA 251

The electrical device nevertheless retains an essential function in the proper management of the work: it serves as a systematic scanning tool. Instead of blindly chipping into the screed at the risk of damaging the pipes of underfloor heating or sampling in a deceptively dry area near an opening, the foreman grids the surface using the electronic detector. This methodical approach makes it possible to isolate the critical point where the destructive measurement must be carried out.

  1. Preliminary gridScan the rooms using the electrical device, noting dark areas, poorly ventilated corners and areas far from heat sources.
  2. Location of the critical pointIdentify the area showing the highest relative value over the entire surface to be accepted.
  3. Destructive samplingExtract the material over the entire thickness of the screed, giving priority to the lower third, away from the immediate vicinity of listed heating coils.
  4. Release destructive testPerform the carbide flask test in accordance with standard SIA 251, record the pressure on the pressure gauge and log the value in the measurement report.

The site manager must therefore draw a clear line in their reports: the electrical diagnosis constitutes an internal decision-making aid to guide checks, while the carbide measurement report remains the sole official document discharging the company in accordance with the provisions of standard SIA 118.

Non-destructive mapping and location of sampling points

On the construction site, the electrical moisture meter, whether it operates by capacitive contact or by resistance between two metal pins, exclusively provides an indicative surface measurement. Screeders and team leaders use it not to pronounce residual moisture compliance, but as a relative and non-destructive detection tool. The device makes it possible to quickly grid a large surface, compare rooms on the same level and clearly identify sectors presenting the highest apparent values. This systematic scanning targets areas with slowed drying: re-entrant angles, door thresholds, areas masked from the airflow by partition walls or surfaces temporarily cluttered by the storage of insulation pallets, bags of binder or heavy tools.

The reliability of these surface readings is heavily altered by two decisive factors: the influence of salts and that of the screed temperature. The high-frequency electrical signal passing through the mortar depends directly on the concentration of free ions in the pore water. During hydraulic setting, the soluble mineral salts of the cement or calcium sulphate binder migrate into the open air and accumulate on the upper crust, creating an extremely conductive surface film. If the screed shows efflorescence or laitance not removed by sanding, the device displays very high electrical values even though the underlying mass moisture is already compliant. Similarly, the mortar temperature modifies the resistivity: a screed that is still warm after the heating cycle overestimates the signal compared to a mortar stabilised at twenty degrees, distorting the estimation in the absence of rigorous thermal correction.

Surface disturbances on the electrical moisture meter and action to be taken
Screed conditionEffect on the electrical signalActual condition in the thicknessMethodical action of the screed layer
Screed warm after heatingArtificially high values due to thermal excitationMass moisture evaporating, unstable thermal profileWait for the mortar to cool completely before any measurement.
Laitance or saline efflorescenceSignificant overestimation of the signal due to ionic concentration at the surfaceNormal moisture under the carbonated filmSand the test area or move the probe to a sound surface.
Surface ventilated by draughtLow values giving the illusion of a ready screedResidual moisture trapped at the core and bottom of the screedImperatively select this sector for destructive core drilling.
Proximity of metal elementsScale saturation by conductive bridgeMoisture without correlation with the measured signalMove the detection area at least 30 cm away from any metal.

From indicative reading to measurement report in accordance with standard SIA 251

The legal value of the reference measurement relies exclusively on the destructive protocol using the calcium carbide flask, prescribed by standard SIA 251. In the event of a defect resulting from premature installation of floor covering (tile detachment, deformation of glued parquet, blistering of resins), the courts and sworn experts rely strictly on recognised rules of the art: no capacitive, dielectric or pin-type reading constitutes an opposable release proof. The screed layer who issues a covering authorisation on the sole basis of an electronic device alone assumes the financial consequences of the claim. This surface instrument is used solely to designate with certainty the exact location where the sample will be extracted, in order to subject the wettest area of the site to the normative reference control.

  1. Systematic grid auscultationWalk across the screed taking regular capacitive readings. Identify variations and mark the highest point where the signal indicates the highest apparent water content.
  2. Manual removal without heatingOpen the area with a chisel and manual club hammer, prohibiting power chisellers whose friction and heating prematurely dry out the extracted mortar.
  3. Sampling in the lower thirdExtract the material from the bottom of the screed bed, where water drains most slowly, while strictly preserving the integrity of any heating pipes.
  4. Calcium carbide reactionCrush the sample in the steel mortar, weigh the exact required mass, add the balls and the reactive ampoule, then shake until the pressure gauge stabilises.
  5. Recording in the reportTransfer the certified manometric value to the official form in accordance with standard SIA 251, with countersignature by the site management.

Dispute over residual moisture: contradictory protocol and legal value

On site, tensions frequently arise when a floor layer blocks the intervention by brandishing an electrical tester with glowing pins, or conversely when a site management demands installation on the basis of a simple favourable capacitive scan. Faced with this disagreement, the site manager or foreman must immediately refuse any arbitration based on this contact data. An indicative surface measurement does not constitute proof of dryness.

To defuse the dispute and legally fix liabilities, the only acceptable approach is to summon the stakeholders for a contradictory sampling according to standard SIA 251. The electrical device then regains its legitimate function: mapping the room to target the coldest, thickest or least ventilated area. It is at this precise location that the screed layer carries out mechanical chiselling to extract the material intended for the reference destructive test.

  1. Written notification of disagreementRemind the site management in writing that electrical values do not exempt from the destructive test protocol provided for the acceptance of the substrate.
  2. Sampling in the lower thirdExtract the mortar over the entire thickness without heating the sample, isolating the lower fraction where residual water accumulates primarily.
  3. Establishment of the official reportRecord the sampled mass, the reaction pressure, the ambient temperature and have the document countersigned by the flooring contractor and the site management.

In the event of subsequent damage such as detachment or blistering, the courts and court experts systematically dismiss electronic moisture meter readings. Only the report of a chemical or gravimetric test carried out in accordance with the rules of the art protects the artisan against a claim for defect of the work within the meaning of the Code of Obligations.

Frequently asked questions

Why does a pin-type moisture meter often indicate a dry screed while it is damp at depth?

The metal pins only penetrate a few millimetres into the hardened mortar. They measure the resistance of the surface film, prematurely dried by draughts or forced ventilation. At the core of the floating slab and in contact with the acoustic insulation, water remains trapped. According to standard SIA 251, only destructive sampling in the lower third reveals the actual water content.

Does an electrical measurement have any legal value in the event of damage to a parquet floor?

No release value. In the event of a dispute brought before the courts, the expert appraisal refers strictly to the quantitative test methods recognised by the rules of the art. An electronic reading is classified as a simple indicative routine check. If the screed layer or the flooring contractor authorised the work without a standardised test report, their civil liability for defective work within the meaning of the Code of Obligations is engaged.

How does the room temperature modify the values displayed by the capacitive moisture meter?

The dielectric constant of water and ionic mobility vary greatly with temperature. A warm screed amplifies the electrical signal, displaying a higher apparent moisture than in reality. Conversely, an unheated construction site in winter masks liquid water under low conductivity. Electronic devices do not compensate for these real thermal gradients, making their figures unusable for validating a covering threshold.

What exact role does the electronic device retain during the acceptance of a cement screed?

The device serves as a rapid non-destructive scanning tool. It makes it possible to cover hundreds of square metres to spot heterogeneous drying zones, water accumulation zones or thermal bridges. It helps the practitioner locate the most unfavourable spot in the room. It is obligatorily at this critical location that the sample must be drilled for the reference destructive test.

Texts and standards cited

  • norme SIA 251Floating screeds and resilient underlays in buildings: execution requirements, dryness criteria and test methods

In the same section