Skip to content
Website
🧱 CFC 281Cement or anhydrite screed: selection and executionChapter 4 of 10 in the section

Water: excess water, lost strength, increased shrinkage and chalking surface

On the construction site, thinning the mortar to pull the screed faster without forcing it is a tempting but destructive reflex. This chapter details the physics of mixing, the drastic drop in compressive and flexural strength, as well as the surface defects caused by free water rising during floating.

Key takeaways

  • An excess of mixing water can destroy up to a third of the final mechanical strength.
  • The optimal water-binder ratio guarantees hydration without generating destructive capillary porosity.
  • Excess water evaporates, creating major dimensional shrinkage conducive to random cracking.
  • Bleeding transports fines to the surface, forming a friable crust unsuitable for receiving a floor covering.

The water-binder ratio determines compactness and strength class

In a traditional cement screed, water serves two distinct functions: chemically hydrating the binder and giving the mortar the plasticity required for its installation. The quantity required for the chemical crystallization reaction alone is small. When the screed layer increases the water supply in the mixer drum to facilitate pumping or screeding with a straightedge, this superfluous water does not participate in the setting process. It occupies a physical volume in the fresh paste, creating a dense network of voids after drying.

Water-binder ratio (W/C)
Quotient of the mass of effective water to the mass of cement in the mix. For a traditional compacted screed mortar, this ratio must range between 0.40 and 0.45 in order to achieve the prescribed mechanical strengths.

Standard SIA 251 sets precise requirements for compressive and flexural tensile strength classes. Moving from a ratio of 0.45 to 0.60 to gain fluidity lowers the 28-day strength by about 30 to 35 percent. A mortar formulated to obtain a C25 class then falls back to the level of a C16 or C20 class. This drop directly compromises the ability of the floating screed to take service loads without indentation, particularly over compressible insulating underlays.

Direct impact of the water-cement ratio on the physical properties of the screed mortar
Water-cement ratioMortar consistencyCompressive strength (28 d)Major pathological risk
0.38 to 0.42Earth-damp, firm compactionCompliant with class C25 to C30Difficulty of compaction if under-dosed
0.45 to 0.50Plastic, easy levellingCompliant with class C20 to C25Moderate shrinkage, controlled porosity
0.55 to 0.65Very fluid, visible bleedingDrop below class C16Chalking, cracking, hollows

Bleeding, differential shrinkage and disintegration of the surface zone

Excess water immediately leads to the bleeding phenomenon: heavy aggregates descend by gravity towards the bottom of the form, while free water migrates towards the finishing surface. This ascending column drains the finest elements of the binder, forming a shiny, pasty film called cement laitance. This upper layer has a locally disastrous water-binder ratio, often greater than 0.80, which deprives it of any abrasive resistance.

  1. 1. Rapid evaporation of free waterUnder the action of building ventilation or construction site draughts, the water accumulated on the surface evaporates too quickly, depriving the surface cement of the moisture required to set.
  2. 2. Formation of a chalking zoneThe silicate crystals do not bind correctly. The upper skin of the screed becomes pulverulent, friable under the fingernail and incapable of withstanding mechanical pull-off stresses.
  3. 3. Plastic shrinkage and crackingThe abrupt volumetric loss related to the departure of water creates internal tensile stresses. The screed shrinks excessively, causing curling at the corners and through-cracks.

This chalking compromises the acceptance of the work by subsequent trades. A chalking floor requires heavy sanding to remove all the unstructured crust down to sound mortar, under penalty of seeing primer coats or adhesives detach due to surface failure. In addition, the increased plastic shrinkage deforms the panels between the fractional joints prescribed by standard SIA 251, lifting the edges and creating voids under the screed at the perimeter strips.

  • Scrupulously respect the mass of water prescribed on the mixer delivery note.
  • Compensate for a punctual need for fluidity with certified plasticising admixtures and not with raw water.
  • Immediately protect the screed that has been pulled from draughts to block early evaporation of the surface film.
  • Perform a hardness test by grid cutting or scratching to check the surface integrity before any sanding.

Mixing drift on the construction site and the drop in mechanical strength

On the construction site, the temptation to add water to the mixer or screed pump is frequent when a team tries to pull the straightedge faster or facilitate passage through the delivery pipes. This action transforms an earth-damp consistency mortar into a fluid and malleable paste, but directly destroys the internal structure of the hardened material. To completely hydrate the cement grains, a quantity of water corresponding to approximately 25 to 28% of the binder mass is sufficient from a chemical standpoint. The additional water added to make the mortar workable remains essentially in a free state, occupying a volume that will inevitably evaporate.

The physical law linking the water-binder ratio to the final strength is unforgiving. As soon as the ratio exceeds the target values prescribed by the factory formulation or standard SIA 251, each litre of excess water interposes itself between the forming calcium silicate hydrates. By evacuating during the first weeks, this free water leaves behind a dense network of capillary micropores and vacuoles. The mineral skeleton loses its compactness. A cement screed initially formulated to achieve a C25 class frequently drops back to the level of a C16 or C12 class under the effect of overconsumption of mixing water, making it unsuitable to withstand the dynamic or static indentations planned in the specifications.

Impact of the water-binder ratio on the performance of a standard-dosage cement screed
Mortar consistencyEffective water-binder ratioCompressive strength at 28 dFlexural strength at 28 dDrying behaviour
Earth-damp (mechanically compacted)0.40 to 0.4525 to 30 N/mm² (class C25)F5 to F6Low shrinkage, homogeneous drying, minimal capillary porosity
Plastic (manual pull-off ease)0.50 to 0.5518 to 22 N/mm² (class C20)F4Moderate shrinkage, increased porosity, extended drying time
Fluid due to excess water (site drift)0.65 to 0.7510 to 14 N/mm² (class C12)F2 to F3Critical shrinkage, random cracking, massive bleeding

Multiplied hydraulic shrinkage, curling and chalking surface

The evacuation of this superabundant water leads to hydraulic shrinkage far exceeding the nominal values expected for a traditional floating screed. This volumetric shrinkage does not occur uniformly throughout the thickness of the work. The upper face, directly exposed to air flows and building ventilation, loses its water much faster than the underside in contact with the polyethylene separation film or the thermal and acoustic insulation. This evaporation gradient generates asymmetrical retraction responsible for the curling of screed slabs.

The corners and edges lift, creating a mechanical cantilever. During the subsequent commissioning of the building or floor loading, these raised edges undergo excessive bending stresses that cause clean breaks along the fractional joints or skirting boards. In addition, the excess water generates continuous bleeding during the setting phase: the water rises to the surface, carrying with it the ultra-fine elements, the clay particles of the sand and the soluble hydrates, while leaving the heavy aggregates to settle at the bottom.

To guarantee the smoothness and pumpability of a screed without destroying its mechanical performance, the screed layer must never adjust the consistency by adding water during pumping. The workability required to work without excessive fatigue is obtained exclusively by adjusting the particle size distribution curve of the aggregates (clean 0/4 or 0/8 sands without polluting fines) and by incorporating standardized water-reducing plasticizers. These admixtures disperse the binder grains by electrostatic repulsion, releasing the water trapped in the agglomerates without degrading the compactness of the matrix. Strict compliance with the proportions provided guarantees internal cohesion, stabilizes dimensional shrinkage and avoids disputes related to a friable surface during the surface cohesion check.

Repair and remediation protocols for a flooded screed

When excess mixing water has ruined the compactness of the mortar, the finding on the construction site is unequivocal: massive bleeding, friable laitance crust, continuous dust underfoot and premature cracking due to differential shrinkage. In accordance with the requirements of standard SIA 251, the screed layer cannot deliver a degraded substrate to the finishing trades. Before any demolition decision, a methodical qualification of the substrate is required to measure the extent of the damage and determine whether mechanical rehabilitation of the surface remains technically viable.

  1. Evaluation of surface and deep cohesionThe site foreman creates a grid by scratching with a chisel or carbide tip to test the mechanical strength. If the mortar crumbles for more than five millimetres or sounds hollow at the corners under the effect of curling, core drillings are prescribed to check whether the loss of strength due to excess water affects the entire thickness of the mortar slab.
  2. Heavy scabbling by shot-blasting or diamond sandingThe chalking surface film must be completely eliminated. Simple sweeping is prohibited: the team uses a heavy floor sander equipped with hard-bond diamond segments or a closed-circuit shot-blaster. The operation strips the non-adherent laitance until sound aggregates and a solid matrix are found.
  3. Industrial vacuuming and deep mineralisationAfter thorough dust removal with an industrial vacuum cleaner, the exposed substrate receives a mineralising impregnator or a fluid solvent-free epoxy primer. This treatment blocks residual fines and consolidates the capillary porosity created by the evaporation of the excess water.
  4. Reconstitution of flatness and crack chasingStabilized shrinkage cracks are bevelled, bridged using corrugated metal staples every twenty centimetres, and poured flush with a two-component anchoring resin. A fibre-reinforced self-levelling smoothing compound then compensates for the loss of thickness following planing.

Frequently asked questions

How to differentiate normal hydration laitance from a chalking surface due to excess water?

Normal laitance forms a regular, thin film of calcium carbonate that is eliminated by standard surface keying sanding. A chalking surface caused by an overdose of water crumbles deeply under the pressure of a fingernail or screwdriver. It continually gives off a white or greyish dust of washed-out cement and reveals a highly porous underlying matrix, hollowed out with vertical bleeding channels unsuitable for receiving any bonding primer.

Why does adding water to facilitate straightedge pulling cause excessive curling?

Excess water migrates to the surface via bleeding, creating a very marked moisture gradient between the bottom and the top of the screed. The upper part, saturated with water and enriched with fines, undergoes hydraulic shrinkage far greater than that of the bottom layer. This differential retraction generates tensile stresses that lift the edges and corners of the floating screed, strongly accentuating the curling phenomenon along the perimeter strips.

Does a plasticising admixture make it possible to make up for mortar mixed with too much water on the construction site?

No. The plasticiser or water reducer must be incorporated during initial mixing to reduce the amount of water required while maintaining workability. If the mixing water has already been introduced in excess into the mixer-pump drum, adding an admixture will not tighten the water-binder ratio. The damage is irreversible: the admixture will further increase fluidity without restoring compactness or preventing the abrupt loss of final mechanical strength.

What site test confirms that a weakened screed can nevertheless be kept?

The check is based on a surface pull-off test using disc bonding according to standard SIA 251. Metal discs are bonded with resin to the stripped surface and then pulled off with a dynamometer. If the measured direct tensile stress reaches the contractual value required for the type of work and failure does not occur within the body of the screed, the substrate may be kept after applying a validated reinforcement system.

Texts and standards cited

  • SIA 251Floating screeds, bonded screeds and screeds on a separation layer: prescriptions for mortar preparation, installation, mechanical strengths and surface condition control

In the same section