Key takeaways
- A flexible wooden floor requires complete mechanical stiffening before pouring any levelling compound.
- The SIA 251 standard prescribes strict requirements for the flatness and stability of the receiving substrate.
- The levelling compound must be highly flexible, fibre-reinforced and reinforced with a mesh.
- The continuous perimeter uncoupling strip prevents any mechanical locking against partitions and walls.
Diagnose deflection and stabilise the timber framing before any pouring
A wooden floor is never an inert substrate. Under live loads or simply people walking across it, floorboards and joists undergo dynamic bending. When a screed layer applies a traditional smoothing compound without structural preparation, the rigidity of the mortar comes into direct conflict with the elasticity of the wood. The shear stress at the interface systematically causes detachment followed by characteristic star-shaped or crazed cracking in the centre of the spans.
The SIA 251 standard governs the requirements for substrates intended to receive floor coverings and screeds. The wooden floor must have sufficient rigidity so that deformation under point loads remains compatible with the planned floor covering. If the floor visibly sinks under the heel or makes repeated creaking noises, the screed layer must suspend work: the underlying assembly requires prior mechanical repair by the wood trades before any application of mineral paste.
- Checking board anchorage: systematic screwing of each board to the joists using partial-thread screws to eliminate vertical play.
- Replacement of rotted or worm-eaten sections: removal of areas degraded by moisture or wood-boring insects.
- Verification of overall flatness using a 2 m straightedge in accordance with the tolerances permitted by the SIA 251 standard.
- Installation of a screwed-and-glued wood-based load-distribution panel if the original floor has thickness discrepancies or excessive spacing between joists.
| Observation on construction site | Mechanical cause | Required action |
|---|---|---|
| Dry creaking underfoot | Board-on-board friction or loose nail | Dense screwing at 20 cm intervals into the joists |
| Marked sagging of a span | Excessive span or under-dimensioned joist | Structural reinforcement by the carpenter prior to work |
| Disjointed boards with through-gaps | Wood shrinkage resulting from hygrometric variations | Flexible joint sealing or bridging to contain laitance |
| Presence of wax or vitrified varnish | Surface layer blocking adhesion | Aggressive bare-wood sanding to open the pores |
Apply a fibre-reinforced self-levelling compound with mesh and perimeter uncoupling
Once the wooden substrate has been cleaned and mechanically stiffened, the application of the compensation layer requires a specific formulation. Only a fibre-reinforced, self-smoothing levelling mortar with a high polymer content, designed to absorb slight micro-deformations without breaking, is used. The incorporated synthetic fibres create a three-dimensional network that resists crack propagation from the moment of hydraulic setting.
- Vacuuming and priming of substratesMeticulously dust the substrate using an industrial vacuum cleaner after mechanical abrading of varnished or painted wood boards.
- Application of the adhesion primerApply a specific bonding primer for closed or wooden substrates by roller, limiting water ingress into the plant fibres and regulating porosity.
- Installation of edge uncouplingFix a compressible resilient strip along the entire perimeter of the room, against skirting boards, partitions, door frames and technical service penetrations.
- Deployment of the textile meshLay an alkali-resistant fibreglass reinforcement mesh over the surface, with a minimum overlap of 10 cm between strips.
- Mixing and pouring of the fibre-reinforced compoundMix the powder using an electric mixer according to the manufacturer's strict water dosage, spread with a stainless steel trowel and de-aerate with a spiked roller.
The nominal thickness of the compound on a stabilised wooden floor is usually between 5 mm and 20 mm depending on the technical specifications of the chosen mortar. The incorporation of a fibreglass mesh, embedded in the lower or intermediate third of the mass, provides the required tensile strength. This reinforcement absorbs local differential movements located right at the joints between boards or chipboard panels.
- Shrinkage-compensated fibre-reinforced levelling compound
- Self-smoothing hydraulic mortar enriched with synthetic resins and short mineral or synthetic fibres, formulated to develop excellent adhesion and increased flexibility without suffering harmful volumetric shrinkage during hardening.
Treatment of singular points and uncoupling at vertical penetrations
On a wooden floor, the fibre-reinforced self-levelling compound forms a thin mineral crust which is not intended to withstand shear movements at hard points in the building. Soil pipe penetrations, heating ducts, door thresholds and hatch frames are all areas of mechanical blockage. If the poured compound grips against these rigid elements or crosses a support discontinuity without precaution, the hygrometric deformations of the timber framing inevitably cause star-shaped cracking or localized detachment.
Edge uncoupling must not be limited to the perimeter of light partitions and masonry walls. It is required around every vertical penetration crossing the floor. The screed layer installs compressible polyethylene foam sleeves or wraps a peripheral uncoupling strip of at least five millimetres thickness around each pipe before pouring. This barrier absorbs the expansion of the tube and prevents the laitance of the fibre-reinforced levelling compound from creating a rigid bridge with the lower load-bearing structure.
| Singular zone | Movement to neutralise | Recommended treatment device | Execution precautions |
|---|---|---|---|
| Perimeter of rooms and skirting boards | Seasonal shrinkage and swelling of wood | Continuous compressible resilient strip fixed at the base of the wall | Keep the strip compressed until the levelling compound has completely hardened |
| Through-going heating pipes | Thermal expansion of metal and joist deflections | Insulating sleeve or flexible gasket tight against grout | Prevent any direct contact between the fluid mortar and the metal |
| Door threshold without floor continuity | Difference in dynamic deflection between two spans | Movement joint profile anchored to the dormant substrate | Align the pouring stop with the axis of the future closed door leaf |
| Stairwell openings or technical hatches | Vibrations induced by traffic and edge stresses | Underlying framing reinforcement and attached edge strip | Check the rigidity of the header joist before closure |
Drying, post-pouring checks and tolerances in accordance with the SIA 251 standard
The behaviour of a fibre-reinforced levelling compound on a wooden substrate requires rigorous management of drying kinetics. Unlike a reinforced concrete slab which tolerates rapid evaporation without changing its geometry, the nailed floor responds immediately to moisture transfers caused by the mixing water of the mortar. Even if the floor was stiffened prior to levelling by tight screwing or screwing of wood-based panels, excessively rapid drying of the surfacing compound impairs its adhesion and hardening.
As soon as setting is complete, the screed layer visually inspects the surface and checks general flatness using a two-metre straightedge. According to the execution specifications of the SIA 251 standard, surface tolerances for a substrate intended to receive a subsequent floor covering require strict regularity, often less than three millimetres under the straightedge. On a timber structure, this performance can only be sustained if the fibre-reinforced and meshed levelling compound has been able to develop its full mechanical strength without suffering premature shocks.
- Protection against draftsClose openings and prohibit any sudden ventilation during the first forty-eight hours to prevent surface drying and crazing of the mineral resin.
- Verification of peripheral continuityEnsure that the perimeter uncoupling strip has not been crushed or submerged by the grout, which would create a rigid anchorage against masonry or partitions.
- Trimming of edge stripsCut excess resilient strip only after the levelling compound has completely dried, just before the arrival of the tilers or parquet layers.
- Checking the residual moisture of the assemblyPerform the necessary measurements to certify that the moisture of the compound and the underlying wooden substrate is compatible with the requirements of the finishing covering.
Management of defects: diagnosis of cracking and remediation of a faulty levelling compound
When the floor begins to sound hollow underfoot or star-shaped crazing appears across a span, the failure almost always reveals uncontrolled dynamic stressing. On a wooden substrate, failure very rarely comes from the smoothing mortar itself, but rather from an underestimation of joist deflection, insufficient screwing of old boards or rigid blocking against vertical walls. According to the requirements of the SIA 251 standard, the bearing substrate must have sufficient rigidity to support the system without excessive deformation.
As soon as defects appear, the foreman carries out a methodical assessment by light percussion to map delamination. If cracking remains localized to a traffic area with an otherwise stable floor, surgical breakout is sufficient. On the other hand, if the crack network runs across the entire room with edge crushing, the installation must be completely removed down to the wooden boarding.
- Removal and exposureChisel out the delaminated area with a flat chisel without damaging the wood fibres. Remove rubble and vacuum up fine dust lodged in the board gaps.
- Mechanical stiffening of the substrateRetighten the screws of each board into the joists using partial-thread screws. If deflection exceeds the permissible tolerance, install a screwed-and-glued load-distribution panel with staggered joints.
- Remediation of uncouplingInstall a polyethylene foam strip of at least five millimetres around the entire perimeter and around pipe penetrations to eliminate any binding points.
- Reconstruction of the reinforced assemblyApply a bonding primer for dry wood substrates, embed an alkali-resistant fibreglass mesh in a first pass, then pour the fibre-reinforced levelling compound.
The joint inspection record of defects and formal notification of timber framing non-compliance to the client allow responsibilities to be redefined before any final repair.
Frequently asked questions
Why does a conventional non-fibre-reinforced levelling compound systematically crack on a wooden floor?
Wood undergoes dimensional variations under the effect of humidity and flexes under foot traffic. Ordinary mineral levelling compound has almost zero flexural tensile strength. Lacking fibers and flexible polymer resins, the hardened mortar tolerates no seating movement. Tensile stress immediately exceeds the internal cohesion of the material, causing interface shear and star-shaped fracturing in the center of mobile spans.
How to check the effectiveness of the perimeter uncoupling strip on a construction site?
The compressible foam strip must surround all walls, temporary skirting boards, door frames and technical column penetrations without any interruption. It must extend two centimetres above the planned finished level. Before pouring, a visual check is carried out to ensure no mortar burrs can fill the space between wood and masonry. Trimming of the excess is done only after complete drying of the levelling compound and installation of the final covering.
Can a significant out-of-plumb be corrected solely with a fibre-reinforced self-levelling compound?
No. Even when fibre-reinforced, a fluid levelling compound on a wooden floor is limited to maximum thicknesses prescribed by the manufacturer, often between ten and thirty millimetres. Too heavy a mineral load worsens the deflection of old joists and dangerously overloads the timber framing. To make up for larger depressions, mechanical shimming, a dry screed of reinforced plasterboards or lightweight levelling granules should be combined before applying a smoothing layer.
What preliminary verification does the SIA 251 standard require on an old wooden floor?
The SIA 251 standard requires checking the flatness, overall rigidity, dryness and cohesion of the substrate prior to any implementation. The screed layer checks the proper anchorage of the boards, the absence of fungal or insect infestation, and ensures that deflection under live loads remains within permitted tolerances. Any excessive movement or biological degradation of the wood justifies suspending work and issuing a written warning to the site management.
Texts and standards cited
- norme SIA 251Floating and bonded screeds based on mineral binders, flatness requirements, tolerances and substrate preparation
