Key takeaways
- The separation layer prevents laitance from penetrating into the underlying thermal and acoustic insulation.
- SIA 251 standard prescribes a minimum strip overlap of one hundred millimetres, sealed for fluid screed.
- Perimeter strips must imperatively protrude above the finished floor level before any mortar pouring takes place.
- A binder leak creates a rigid acoustic bridge that cancels out the impact sound insulation efficiency.
Ensure laitance tightness through methodical strip overlapping
- Separation layer
- Synthetic sheet, generally made of polyethylene at least 0.2 mm thick, placed between the insulation and the screed to prevent mixing water and laitance from penetrating into the resilient underlayer.
The polyethylene film fulfils an essential mechanical and physical function according to SIA 251 standard. When pouring the screed, especially with self-levelling fluid mortars based on cement or calcium sulphate, the liquid binder seeks out the slightest discontinuity. Without perfect tightness, this laitance infiltrates the interstices of the polystyrene or mineral wool insulation panels. Upon hardening, it forms rigid blocks that bond the screed to the raw slab, destroying the impact sound reduction planned by the project.
| Screed type | Minimum overlap | Joint treatment | Main risk |
|---|---|---|---|
| Traditional screed (earth-damp) | 100 mm | Careful loose overlap | Displacement of strips under wheelbarrow traffic |
| Fluid or self-levelling screed | 150 mm | Continuous bridging with waterproof adhesive tape | Infiltration under pressure from fluid laitance |
The behaviour of the film under the movement of work crews and pumping hoses requires continuous vigilance. On flexible resilient insulation, the membrane tends to form folds under foot traffic. The installation of overlaps must strictly be carried out in the direction of pouring progress to prevent the mortar flow from working its way under the loose edges. When technical pipes cross the compensation insulation, the film must conform to the geometry without undergoing mechanical tension, under penalty of bursting during the overload induced by the fresh mortar thickness.
Lock the perimeter and penetrations to eliminate acoustic bridges
Lateral decoupling constitutes the direct vertical extension of the separation layer. The resilient perimeter strip, provided with a flexible polyethylene skirt, guarantees discontinuity between the structural work and the floating structure. SIA 251 standard specifies that the screed must not come into contact with any rigid vertical element: load-bearing walls, lightweight partitions, door frame bases or riser columns. The perimeter insulation strip and its waterproofing film form a truly watertight tub that receives the mixture.
- Fixing the perimeter strip at the edgeInstall the resilient strip along all walls and pillars without tensioning it in internal corners, in order to avoid the bow-string effect which creates a gap prone to mortar penetration.
- Connecting the skirt to the horizontal sheetFold the waterproof flap of the edge strip over the floor separation film, then lock the junction over its entire length using a waterproof fabric adhesive tape.
- Watertight treatment of vertical penetrationsWrap pipe sleeves in a resilient insulating sleeve, pull the film up around the pipe and secure the assembly with tight adhesive tape to block the laitance.
- Final visual inspection before authorizing the pourInspect the entire compartment to identify accidental perforations, repair tears with a glued patch and check the continuous height of the edge.
Any perforation of the film caused by levelling tripods, measuring rods or screeding rules must be repaired immediately on site. The installer applies a polyethylene patch extending at least ten centimetres around the tear, fixed with a moisture-resistant adhesive. This rigor ensures the mechanical independence of the floating screed and preserves the integrity of the insulation against attacks by the binder.
Mechanism of rigid bridge formation and performance degradation
The decoupling of a floating screed relies on an uncompromising physical principle: no rigid connection must be established between the fresh mortar and the load-bearing structure or the underlying thermo-acoustic insulation. When a polyethylene film strip suffers a gap, an unbridged tear or insufficient overlap during pouring, the mixing water laden with binder instantly infiltrates beneath the separation sheet. This liquid laitance insinuates itself into the interstices between the thermal or acoustic insulation panels, penetrates the porosity of the mineral fibres or fills the residual space against the concrete slab.
Upon hardening, this infiltration forms an undeformable mineral column, referred to as a rigid bridge or acoustic bridge. The presence of a single point of direct contact ruins the mass-spring-mass effect guaranteed by the insulation system. The impact sound reduction measured in situ drops drastically, rendering the structure non-compliant with building noise protection requirements. Mechanically, the setting of the laitance locally anchors the screed to the rigid structure, blocking the free hydraulic shrinkage of the floating slab during its desiccation. Shear and tensile stresses concentrate vertically above the blockage, causing premature surface cracking and spalling along the perimeter connections.
| Film execution defect | Laitance pathway | Acoustic pathology | Mechanical disorder |
|---|---|---|---|
| Overlap less than 100 mm without adhesive tape | Infiltration under the overlap by capillarity and grout load | Increased lateral transmission of impact noise to the floor below | Random cracking by blocking dimensional shrinkage |
| Perimeter strip placed without a flap taped to the film | Leakage behind the compressible foam along the masonry | Complete acoustic short circuit with partitions and party walls | Edge lifting and screed spalling during thermal variations |
| Point tear of the film by wheelbarrow traffic or treading | Filling of compressible or thermal insulation cavities | Local loss of resilience of the acoustic underlayer | Differential settlement under point load and local sagging |
| Poorly folded pleat or tensioned film in internal corners | Tearing of the film under the weight of fresh mortar during trowelling | Creation of a rigid concrete wedge sealed at the base of the wall | Corner bursting and blocking of heating screed expansion |
Edge implementation and film management up to finishing
To eliminate any risk of parasitic transmission, SIA 251 standard requires methodical execution of the decoupling envelope. The extruded polyethylene foam perimeter insulation strip must be installed continuously around the entire periphery of rooms, along load-bearing walls, lightweight partitions, columns and around each pipe passing through the floor. This perimeter strip generally incorporates a flexible plastic flap fixed at the lower part. The horizontal separation film covers this flap over a minimum width of 100 millimetres, the whole assembly being sealed using a high-adhesion waterproof adhesive tape in order to prevent any backflow of cement paste.
The upper edge of the perimeter strip and the protective film must mandatory protrude above the finished level of the screed by at least 20 to 30 millimetres. This excess height protects the edge of the screed against overflows during levelling, screeding rule passing or mechanical trowel passing. This protrusion forms a waterproof bulwark against laitance splashes which, by drying against a wall plaster or brick block, would establish an undesirable airborne acoustic bridge.
- Setting out and alignment of the compressible stripUnroll the perimeter strip against vertical walls without exerting mechanical tension, ensuring perfect contact in angles without forming curves in internal corners.
- Deployment and joining of polyethylene stripsLay the separation film respecting the overlap prescribed by SIA 251 standard. Secure the joints over their entire length using fabric adhesive to withstand the pulling stresses of discharge hoses.
- Sealing of the perimeter flapFold the waterproof flap of the perimeter strip onto the horizontal film layer and glue the interface continuously to form an airtight basin.
- Preservation of excess lengths until flooringKeep the compressible strip and protruding film intact throughout the drying and curing period of the screed. Prohibit any premature trimming by other trades.
Trimming the perimeter decoupling strip is a critical operation whose temporal responsibility must be clearly assigned. The screed layer must never cut the edge strip flush with its fresh or hardened mortar. This cutting falls exclusively to the floor covering installer (tiler or flooring layer), immediately prior to fixing skirting boards. Cutting too hastily exposes the screed edge to falling tile adhesive during tile installation or when pouring self-levelling finishing smoothing compounds, thus destroying all the decoupling work carried out during the screed structural work.
Claim management: laitance leak, acoustic bridge and targeted repairs
When the tightness of the separation film yields under the pressure of the mortar or embedding fluid, the laitance immediately infiltrates into the interstices of the thermal or acoustic insulation. This infiltration polymerizes upon contact with panels or flakes, transforming a resilient mat into a compact block of mortar. The result is direct: a rigid bridge solidifies the screed with the raw slab or vertical walls, ruining impact sound insulation and violating the requirements of SIA 251 standard.
- Detection and delineation of rigid contactDiagnosis is carried out by acoustic measurement or during a visual inspection at the periphery if the edge strip has sagged. The rigid zone is located by probing the edges or by observing abnormal shrinkage cracking caused by the blocking of horizontal movements.
- Peripheral mechanical clearanceIf the rigid bridge is located at the edge due to lack of film upturn, a rail-guided circular saw cut makes it possible to open a clean joint over the entire thickness of the screed. Mortar infiltrated against plaster or masonry is cleared out with a flat chisel.
- Clearing and local repair on insulationWhen the laitance leak has crossed the strip overlap in the main field, the screed must be sawn and cleanly demolished over the saturated area. Cement-hardened insulation is extracted, then replaced with new material of identical compressibility.
- Reconstitution of the watertight liningBefore backfilling with a fast-setting binder or shrinkage-compensated mortar, film continuity is restored. A new strip of polyethylene is slid under the existing screed with an overlap of at least 200 mm and glued with waterproof tape.
Once the opening has been cleaned up and the insulation reconstituted without any rigid contact, the repair pour is carried out taking care to ensure perfect decoupling of the joint. This methodical protocol restores the floating function of the structure without requiring total demolition of the package.
Frequently asked questions
What minimum overlap width must be observed for the film strips under the screed?
According to professional rules and SIA 251 standard, the minimum overlap between two polyethylene film strips is 100 to 150 mm for a traditional compacted screed. For a cement or calcium sulphate fluid screed, the overlap reaches at least 200 mm and requires systematic bridging with waterproof adhesive tape over the entire length to prevent the suction of liquid laitance.
How should the perimeter upturn of the film along skirting boards and vertical walls be treated?
The separation film or the flap attached to the perimeter strip must run continuously up all walls, columns and technical ducts. This upturn must imperatively protrude above the finished level of the screed and the final floor covering. This excess is only trimmed at the precise moment of installing skirting boards or the finishing joint of the covering.
Why does a laitance leak destroy the acoustic insulation of the structure?
Impact sound insulation relies on the mass-spring-mass principle, where the screed floats freely on the resilient insulation. If liquid laitance passes through the film, it fills the pores of the insulation and solidifies as it dries. This block of concrete creates a hard acoustic bridge between the slab and the screed, directly transmitting impact vibrations to the load-bearing structure of the building.
Can standard site polyethylene be used as a waterproof separation film?
No, a light protective film like a painter's tarp is prohibited. The separation film must exhibit sufficient mechanical resistance to puncture and tearing during pouring and worker traffic. A polyethylene sheet of at least 0.2 mm (200 microns) thickness is usually used, free of holes, laid flat and without major folds on the insulation.
Texts and standards cited
- SIA 251Screeds inside buildings: requirements relating to insulating underlayers, perimeter decoupling and separation layers
