Skip to content
Website
🧱 CFC 244Acoustics: silencers, transmission and room noiseChapter 4 of 10 in the section

Noise travelling through the structure: fixings, clamps and rigid contacts

A ventilation duct vibrates under the effect of air turbulence and the fan motor. If a clamp without a resilient lining or a clamped threaded rod comes into direct contact with the concrete, low frequencies spread through the building. You will learn to install decoupled hangers and to track down every acoustic bridge before acceptance of the work.

Key takeaways

  • The SIA 181 standard sets strict noise immission requirements in adjacent sensitive rooms.
  • Every hanger clamp must include a resilient lining with no mechanical bridge via the rods.
  • A single firm contact with a slab or reinforcement instantly transmits structure-borne noise.
  • The tactile and acoustic check during commissioning reveals parasitic connections.

Structure-borne transmission mechanisms and SIA 181 requirements

In operation, an air-handling system subjects the air ducts to continuous dynamic stresses: pressure pulsations from the fan blades and air turbulence at bends and fittings. These variations make the galvanised sheet-metal walls vibrate. If the network is suspended without anti-vibration decoupling, the kinetic energy is converted into a structure-borne wave injected directly into the structural work. Reinforced concrete absorbs low frequencies, from 50 Hz to 250 Hz, very poorly. The vibrations travel through it without significant attenuation over several floors before radiating into sensitive rooms as a continuous dull hum.

On construction sites, the defect commonly stems from an unintentional rigid contact that appeared after installation. It is enough for a duct to touch a reinforcing bar left in an opening, or for a partition profile to press against the duct, to short-circuit the insulation. The passage through fire-resistant separations is a critical point: sealing a duct with hard mortar without inserting an elastomer strip bonds the sheet metal to the masonry. All the vibrational energy of the duct then spreads directly into the floor or the cross wall.

Origin of rigid bridges and transmission into the structures
Fixing or penetration pointCommon workmanship defectConsequence for the structure
Ceiling anchorClamped threaded rod without resilient elementSpread of low frequencies into the concrete slab
Circular duct clampInstallation without soft elastomer liningDirect transmission of vibrations from sheet metal to clamp
Passage through cross wall or slabMortar sealing without decoupling stripDuct embedded and radiating into the wall
Narrow plenumDuct wedged against reinforcement or a railMechanical bridge cancelling the decoupled support

Installing decoupled clamps and tracking down bridges at commissioning

To break the transmission chain, the support system must act as a continuous mechanical filter. For circular networks, the fitter must install a clamp with a resilient interposed layer, fitted with a vulcanised EPDM elastomer rubber seal inserted in its groove. This profile eliminates any direct contact between the sheet metal and the metal strap. For rectangular ducts, the hanger cross-members must be fitted with anti-vibration washers under the fixing head or resilient pads under the corners of the duct. The resilient element must be sized to the suspended load: a mount that is too rigid filters no vibration, whereas a material that is too soft is completely crushed under the weight of the pipework and loses its damping capacity.

Clamp with resilient interposed layer
Metal fixing clamp fitted with an inner lining of resilient elastomer, isolating the sheet metal to block the transmission of structure-borne vibrations to the rod and the load-bearing structure.
  1. Visual check along the entire routeCheck along the route that a clear gap of at least 20 mm separates the sheet metal from slabs, reinforcement and secondary profiles.
  2. Checking that the rods are plumbCheck that the threaded rods are perfectly vertical to avoid any metal-to-metal jamming against the holes of the anchor brackets.
  3. Dynamic test at nominal flowStart the supply and extract fans manually at 100% of their speed to induce maximum resonance of the network.
  4. Touch and sound inspection of the hangersTouch each rod to detect abnormal vibrations, and place the blade of a screwdriver against the anchor to listen to the noise transmission.

The identification of acoustic bridges at commissioning must take place before the technical ducts are closed and the suspended ceilings are finally fixed. As soon as the installation runs at nominal flow, the fitter methodically inspects each hanger. If a threaded rod vibrates noticeably under the fingers or transmits a crackling sound when sounded, the mechanical bridge must be located and removed without delay: cutting back a rod that is too long and bottoms out in a hole in the slab, realigning a clamp to free a side in contact with an angle bracket, or fitting a dense mineral wool shell around a penetration sleeve. This systematic check protects the company against acoustic disputes at handover of the work.

Origin of unintentional rigid contacts and transmission through the structure

The acoustic control of an air-duct network does not depend solely on the effectiveness of baffle silencers or aerodynamic balancing. Even when the air-handling unit rests on anti-vibration mounts and the connections are fitted with flexible sleeves, the pulsations generated by the fans travel as vibration waves in the sheet metal of the ducts. If a duct comes into direct mechanical contact with the frame of a building, this vibration is transmitted instantly to the structural mass. The reinforced concrete slab then behaves like a giant acoustic membrane, spreading a low-frequency hum to the adjacent dwellings or offices.

Structure-borne acoustic bridge
Direct, rigid mechanical connection between an active vibrating element (ventilation duct, fan, motorised damper) and the load-bearing structure of the building, short-circuiting the elastic isolation devices and transmitting the vibrational energy as structure-borne noise.

On construction sites, sound bridges almost never result from a total omission of fixings, but rather from assembly carelessness when fixing the networks. A single clamp with a resilient interposed layer that is badly positioned or crushed neutralises the vibration isolation of an entire run. Unintentional rigid contact is the most common trap: a duct diverted to clear an obstacle and resting against the edge of a core-drilled hole, a self-drilling screw that is too long whose tip rubs against a metal beam, or a threaded rod screwed hard against the bottom of a mounting rail without an insulating washer.

Analysis of common rigid contacts and decoupling corrective measures
Critical installation pointNature of the rigid contactImpact on the structureDecoupling measure
Hanging by circular clampExcessive tightening compressing the elastomer down to the metalDirect transmission of the fan rotation frequencyTightening to controlled torque while preserving the effective thickness of the EPDM lining
Passage through slab or load-bearing wallMortar sealing or rigid foam in contact with the sheet metalSpread of turbulence vibrations into the structural workSleeving with mineral wool mat or elastomer collar with no hard point
Support on rail under slabThreaded rod in firm contact with the support profileShort-circuiting of the upper elastic suspensionFitting of nuts with vulcanised rubber anti-vibration washers
Technical crossing in suspended ceilingDuct resting on a hanger of another tradeResonance of the light rails and plasterboardMaintaining a continuous clear gap and fitting resilient protective shells

Protocol for locating acoustic bridges and bringing them into compliance

The requirement for acoustic comfort demands strict compliance with the criteria defined by the SIA 181 standard. This standard sets the permissible noise limit values for technical installations in dwellings and workplaces. At acceptance of the work, the client checks the conformity of the installation in accordance with the Code of Obligations (CO). If abnormal structure-borne noise is detected, the ventilation contractor must precisely identify the origin of the transmission before any major expert investigation.

  1. Sequenced start-up of the installationsStart the air-handling unit at reduced speed, then increase in successive steps up to maximum flow. Selective listening makes it possible to identify at which airflow speed the vibrations resonate with the slab or the walls of the building.
  2. Tactile and stethoscopic tracking along the routeWalk the distribution line from the plant room, placing a hand on each hanger and clamp. A threaded rod that vibrates markedly under the fingers indicates an insulation defect at its end or an asymmetrical load transfer.
  3. Checking penetrations and openingsVisually inspect the gap between the duct and the edge of the core-drilled holes. Pass a thin shim or a steel rule around the whole perimeter of the opening to make sure there is no rubble, cement grout or direct contact with the reinforcement.
  4. Isolation of terminal equipmentCheck the decoupling of the supply or extract plenums built into lined partitions. Check that the fixing screws of the diffusers do not create a rigid contact with the metal framing of the linings.

Identifying acoustic bridges at commissioning makes it possible to correct construction site anomalies immediately without destructive work. Replacing a rigid support with a spring hanger, loosening an over-compressed clamp or cutting away a concrete burr around a duct eliminates almost all transmitted humming. The installer records these interventions in the commissioning report in order to guarantee the final conformity of the work with the contractual and standard requirements.

Emergency procedure in case of residual acoustic non-conformity

When the acoustic acceptance measurements reveal that the permissible values of the SIA 181 standard are exceeded in sensitive rooms, the cause almost systematically lies in a direct mechanical connection that has gone unnoticed. A direct metal clamping on the air-duct network immediately turns the concrete floor into a resonator for the fan rotation speed. In front of the client, the installer must act methodically before considering major modifications to the silencers or the air velocity.

  1. Isolating the source and frequency checkThe unit is controlled in steps of 10% of flow. The acoustician records the third-octave band spectrum in the room in dispute. The presence of a peak locked on the rotation frequency or the blade-passing frequency confirms transmission through the duct casing and immediately rules out an airflow problem.
  2. Tactile sounding and mechanic's stethoscopeThe foreman walks the entire distribution route from the plant room to the disputed penetration. Each clamp with a resilient interposed layer is felt by hand, then with a screwdriver or a workshop stethoscope placed on the threaded rod. A vibration perceptible at the anchor points to a pinched elastomer sleeve, a metal washer in oblique contact or a nut locked against the angle iron without an anti-vibration ring.
  3. Careful inspection of the masonry interfacesSlab and cross-wall penetrations must be inspected at the level of the sleeves. Any unintentional rigid contact, such as a cement burr, a trapped pebble or plaster injected directly against the sheet-metal duct without surrounding mineral wool, must be cleared with a hand chisel without damaging the sheet metal.

Once the anomaly has been located, releasing the load and replacing the fixing allows an immediate readjustment of the sound levels. If the bridge persists despite reworking the clamps, adding an extra flexible textile sleeve at the outlet of the plant room cuts the propagation before it enters the vertical technical duct, thus protecting all the floors.

Frequently asked questions

How can you quickly tell structure-borne noise from airborne noise at a ventilation outlet?

The most direct method is to press a mechanic's screwdriver against the wall of the room with your ear on the handle. If the dominant frequency of the hum is clearly perceived through the concrete slab or wall while the noise disappears when the supply grille is removed, it is structure-borne transmission via the fixings of the network.

What maximum compression should be tolerated on the elastomer strip of a circular duct clamp?

The rubber or EPDM elastomer strip built into the clamp must be compressed by about 20 to 30% of its free thickness when tightening the side screws. Excessive tightening that brings the clamp's sheet metal into metal-to-metal contact with the duct destroys the insulating capacity of the resilient component and re-establishes a firm acoustic bridge to the threaded rod.

Can rigid angle brackets be used to fix rectangular ducts under an occupied slab?

No. Screwing a perforated angle bracket directly onto the sides of a sheet-metal duct without a damping element is prohibited under rooms requiring acoustic comfort according to SIA 181. Trapezoidal reinforced-rubber dampers must be fitted, or the duct must be hung on a support rail decoupled by resilient acoustic washers under the nut.

What should you do when an acoustic clamp still transmits vibrations to the floor above?

The natural frequency of the suspension system should be checked. If the standard resilient interposed layer is too rigid for the mass of the duct at low flow, it does not attenuate the critical frequency of the motor. Installing an acoustic spring hanger or an elastomer mount of suitable Shore hardness between the rod and the slab solves the problem.

Texts and standards cited

  • SIA 181Protection against noise in buildings
  • SIA 118General conditions for the execution of construction work

In the same section