Key takeaways
- Pushing the frequency beyond the nominal point makes the power absorbed rise with the cube of the speed.
- Measuring the phase current with a True RMS clamp meter protects the motor windings.
- The actual operating point is set by differential pressure measurement and direct airflow measurement.
- Rigorous pulley alignment and measured belt tension prevent energy losses and vibrations.
The over-frequency trap: when forcing the drive overloads the motor
On construction sites, there is often a temptation to push the variable-frequency drive above 50 Hz to compensate for a lack of airflow at the terminal outlets. This reaction almost always masks a balancing error, an undersized network or a closed damper. The laws of fan aerodynamics state an unforgiving physical rule: if the airflow increases in proportion to the rotational speed, the required pressure varies with the square and the power absorbed at the shaft increases with the cube of that speed. Forcing the frequency quickly turns a quiet machine into a source of nuisance and places the electrical winding under overload.
The CFC 244 technician never approves a cabinet setting without measuring the current drawn on each supply phase of the motor under real operating conditions, with dampers open and filters clean. The measurement is taken with a True RMS clamp multimeter at the drive output or at the local isolator. The measured value must always remain less than or equal to the rated current shown on the manufacturer's nameplate for the selected connection (star or delta at the operating voltage).
| Drive frequency | Relative airflow | Total pressure | Power absorbed | Sound level in casing |
|---|---|---|---|---|
| 40 Hz | 80% | 64% | 51% | In line with the selection |
| 50 Hz (nominal) | 100% | 100% | 100% | Guaranteed acoustic level |
| 55 Hz | 110% | 121% | 133% | +4 dB(A), clearly audible airflow noise |
| 60 Hz | 120% | 144% | 173% | +8 dB(A), risk of stall |
Artificially raising the speed also generates mechanical vibrations and destructive turbulence at the volute and the reaction impeller. According to art. 22 OLT 3, noise and vibrations at the workplace must be avoided or combated, as a priority, by measures applied to the operating installations. When the fan roars in the plant room, the primary cause is an undiagnosed network pressure loss rather than an undersized machine.
Measuring the actual operating point and kinematic check of the transmission
To locate the operating point precisely on the manufacturer's fan curve, reading the frequency is not enough. The refrigeration or ventilation fitter measures the differential static pressure across the impeller using an electronic differential manometer connected to the piezometric pressure taps of the casing or of the inlet measuring orifice. This reading immediately converts the measured depression into mass flow through the calibration coefficient K specific to the impeller.
- Initial airflow readingConnect the differential manometer to the pressure tap of the fan's inlet ring. Read the differential pressure Δp in pascals and calculate the airflow using the manufacturer's relation linked to the K factor.
- Electrical check at the setpointMeasure the current drawn on the three phases with a clamp ammeter. Check the phase balance and compare the measured current with the rated current shown on the motor nameplate.
- Adjusting the frequency rampAdjust the maximum speed parameter in the drive to cap the setpoint at the airflow prescribed by the airflow balancing report, without exceeding the permissible current.
- Mechanical check of the transmissionFor units driven by V-belts, check the pulley alignment with a precision straightedge or a laser, then adjust the deflection under load with a mechanical tension gauge.
On indirect-drive fans, the overall efficiency depends directly on the condition of the V-belts. An under-tensioned belt slips on the pulley flanges, loses several dozen revolutions per minute and overheats until it breaks. Conversely, excessive tension crushes the impeller bearings and destroys the motor's ball bearings under abnormal radial stress. The angular and axial alignment of the two pulleys must show an error of less than 0.5 degrees to avoid asymmetric wear of the belt flanks and the generation of parasitic sound harmonics.
In-situ validation: comparing the current draw with the nameplate data
On an air handling unit, trying to make up for an airflow deficit by blindly increasing the drive's output frequency is a common operating error. If the duct networks have unforeseen singular pressure losses, sharp bends without guide vanes or throttled balancing dampers, the fan works against excessive resistance. According to the fan affinity laws, the airflow varies in proportion to the rotational speed, but the power absorbed at the shaft increases with the cube of that same speed. Trying to force air through an undersized network immediately makes the electricity bill soar without delivering the required volume to the diffusers.
The true RMS (TRMS) clamp ammeter reveals this runaway without ambiguity. At commissioning, the current must be measured on each of the three supply phases of the motor downstream of the drive, with the casing fully closed and new filters in place. This reading is immediately compared with the rated current noted on the manufacturer's nameplate for the selected connection (star or delta at 400 V). A motor whose measured current exceeds the nameplate value runs in continuous thermal overload: the winding heats up, the thermal trip is imminent and the acoustic level of the unit becomes unbearable, generating dull turbulence noises in the distribution ducts.
| Measured parameter | Design nominal point (50 Hz) | Over-frequency drift (58 Hz) | Deviation and site impact |
|---|---|---|---|
| Supply airflow | 10,000 m³/h | 10,800 m³/h | +8% (useful airflow far from expectations) |
| Calculated total pressure | 650 Pa | 874 Pa | +34% (increased network resistance) |
| Measured current draw | 8.2 A (nameplate nominal: 8.5 A) | 11.1 A | +35% (motor clearly in thermal overload) |
| Measured active power | 4.3 kW | 6.7 kW | +56% (major energy overconsumption) |
| Sound level in duct | 64 dB(A) | 73 dB(A) | +9 dB(A) (intolerable airflow whistling) |
Belt transmission: alignment, tension and impact on the power drawn
On ventilation units driven by V-belts, setting the operating point demands absolute mechanical rigour beforehand. Before adjusting a single hertz on the frequency converter screen, the drive train must be perfectly aligned and tensioned according to factory specifications. A poorly adjusted transmission dissipates energy as heat and parasitic friction, distorting the assessment of the motor current and prematurely degrading the impeller bearings.
- Checking the geometric alignment of the pulleysPlace a ground aluminium straightedge across the outer faces of the driving and driven pulleys, or use a magnetic laser alignment tool fixed in the grooves. Angular parallelism errors (maximum tolerance less than 0.5 degrees) and axial offset of the grooves must be corrected without fail. Any misalignment forces the belt flanks to be guided, causing continuous mechanical resistance and a characteristic squealing noise.
- Setting the mechanical preload tensionUse the threaded rods of the motor cradle to move the motor axis away from the fan axis. Tension is measured with an acoustic tension meter reading the natural frequency (Hz) or with a mechanical spring gauge measuring the resulting deflection (in mm) under a specified pushing force at the centre of the free span. An over-tensioned belt radially overloads the bearings and raises the no-load current by 10 to 15%. A belt that is too slack slips in the grooves, causing a loss of rotation that leads the operator to force the drive frequency unnecessarily.
- Running-in and re-measuring the current under loadRun the unit for two hours at the nominal frequency of 50 Hz. Stop the machine, lock off the local padlockable isolator, then immediately check the temperature of the grooves and the residual tension after the elastomer has relaxed. Adjust the final tension, close the casing seal again and take the current draw readings again, phase by phase.
The actual operating point is obtained by cross-checking the overall airflow measurement (taken with a differential pressure measuring cross on the inlet bellmouth or with a calibrated differential manometer) and the static pressure available at the duct connections. If the airflow remains below the hygiene requirements while the motor current reaches the nameplate value at 50 Hz, it is strictly pointless to unlock the drive to 60 or 70 Hz. The solution lies exclusively in correcting the airflow network: opening fire dampers left partially engaged, replacing turbulent branch connections, reworking duct sections or changing the physical ratio of the pulley diameters.
Arbitration procedure in case of airflow drift and overconsumption
When the contractual airflow remains unattainable without pushing the variable-frequency drive beyond the motor's tolerances, forcing the parameters is a technical fault. A motor-fan unit running at electrical saturation causes destructive heating of the windings and transmits excessive vibrations to the ducts. According to art. 22 OLT 3, noise and vibrations must be avoided or combated by construction measures, measures on the operating installations or isolation of the sources. Pushing the setpoint to 55 or 60 Hz to overcome an undersized network multiplies the sound level in the duct without restoring the expected dynamic pressure.
- Isolating the airflow measuring pointRead the total static pressure at the unit's flanges with a calibrated differential manometer. Immediately compare this value with the fan manufacturer's curve to check whether the measured operating point lies in a stall zone.
- Electrical check under real loadMeasure the current drawn on each phase at the drive output with a True-RMS clamp meter. If the measured value exceeds the rated current shown on the motor nameplate, lower the frequency setpoint.
- Mechanical diagnosis of the drive couplingCheck the tension and alignment of the V-belts. Excessive tension needlessly overloads the motor bearings and increases the resisting torque, absorbing several extra amperes with no gain in airflow.
- Inspection of the upstream and downstream air networkCheck that the balancing dampers are fully open, that the filter cells are clean and the position of the fire dampers, to rule out an accidental singular pressure loss.
If the network shows abnormal resistance due to overly sharp changes of direction or underestimated sections, the installer records his measurements in a complete balancing report. He informs the site management of the actual pressure losses so that airflow modifications can be undertaken rather than forcing the machine outside its operating range.
Frequently asked questions
Why does my drive display a higher current than the motor's rated value?
This situation occurs when the setpoint frequency exceeds the nominal frequency without adapting the voltage-to-frequency ratio, or if the fan is moving air that is too dense during tests in cold weather. Excessive belt tension or a network with less resistance than expected also moves the fan towards too high an airflow, increasing the power drawn beyond the limits of the winding.
How do I identify a belt alignment problem during commissioning?
A lack of coplanarity or parallelism between the driving pulley and the driven pulley shows up as a continuous whistling, premature wear of the flanks and black rubber dust thrown into the casing. The check is made with a ground straightedge or a laser aligner to ensure an angular and axial deviation below the usual tolerances of transmission manufacturers.
Can the terminal dampers be throttled if the fan runs at its minimum frequency?
Throttling the terminal dampers needlessly increases the static pressure of the network, generates air-crushing noises at the diffusers and wastes electrical energy. If the unit still delivers too much air at the minimum frequency allowed by the drive for motor cooling, the mechanical ratio must be corrected by changing the pulleys or the speed control settings must be adapted.
What is the reliable method for setting the operating point on the manufacturer's curve?
The fitter measures the total differential pressure between the fan inlet and outlet, then measures the actual rotational speed with an optical tachometer. Cross-checking these values with the airflow measurement by measuring cross or exploration sleeve makes it possible to plot the operating point precisely on the fan charts and deduce the effective efficiency.
Texts and standards cited
- OLT 3 art. 22noise and vibrations: they must be avoided or combated (construction measures, measures on the operating installations, isolation or insulation of the sources, work organisation).
